CategoriesServices

Wholesale Drains and Shower Channels: Buying Guide for Turkey

siphons caniveaux douche gros turquie
TPI / Buyer intelligence
Reading progress6 min read
ReviewedNov 2026
Executive answer01

TL;DR: When buying sanitary drainage products wholesale, separate floor drains, plugs and basin wastes, and linear shower channels. For each reference, define the dimensions, outlet direction and diameter, material, grate, required flow rate, water seal or anti-odour device, cleaning access and the interface with waterproofing. Have…

Commercial benchmarkTechnical contextLogistics basis

TL;DR: When buying sanitary drainage products wholesale, separate floor drains, plugs and basin wastes, and linear shower channels. For each reference, define the dimensions, outlet direction and diameter, material, grate, required flow rate, water seal or anti-odour device, cleaning access and the interface with waterproofing. Have a sample tested with the project’s pipes and finishes, then confirm spare parts, packaging and MOQ. The TPI category of drains, plugs and channels helps you structure this bill of materials.

Distinguish Between Sanitary Drainage Products

ProductKey informationPurchasing risk
Floor drainDimensions, grate, vertical or side outletOutlet incompatible with the floor opening
Basin plug and wasteOpening, overflow, mechanism and connectionWrong thread or clearance problem under the basin
Linear channelLength, width, outlet, grate and feetIncorrect interface with slope and waterproofing
Grate or trim pieceMaterial, pattern, load rating and fixingDecorative piece not compatible with the body
Maintenance accessoryBasket, water seal, gasket and removal toolCleaning or replacement not possible

Do not lump these products together under a single “plumbing accessories” line. Each family needs its own reference, quantity and drawing. For a hotel or residential project, link the references to the bathroom schedule to check compatibility with basins, showers and wall and floor finishes.

Check Dimensions, Outlets and Connections

The supplier must receive the dimensions of the body, the visible part, the floor opening and the connection. Specify whether the outlet is vertical, horizontal or side, its nominal diameter and the type of connection planned. Also check the height available in the screed or under the basin.

For a channel, state the visible length, width, outlet position, adjustment options and finished floor level. For a basin waste, check the basin opening, whether there is an overflow, the closing mechanism and the space in the vanity unit. A model that looks similar can still be incompatible with the actual installation.

  • Reference, quantity and destination room
  • Dimensions of the body and of the visible finish
  • Outlet diameter, direction and position
  • Installation height and adjustment range
  • Connection type and associated pipe
  • Accessories, gaskets and cleaning parts included

Compare Materials, Grates and Finishes

Ask for the material of the body, the grate, the plug and the internal parts. A “stainless-look” description does not confirm that all parts are made of the same material. Also check the thickness, the finish, the welds or joints, the edges and the resistance expected for the intended use of the room.

The visible finish should be coordinated with the taps and other accessories when the project requires it. Approve a physical sample rather than a photograph. Check for differences in colour and brushing under the same lighting, and how easily the grate can be removed without damaging the surface.

Check Flow Rate, Water Seal and Odour Protection

The effective flow rate depends on the product, the connection, the available height and the installation. The specification should state the expected flow rate or evaluation method. Ask for the data or test results for the exact model, then check that the capacity of the downstream network remains consistent.

For odour control, identify the water seal, membrane, valve or other device used, along with its operating and maintenance conditions. A rarely used room may behave differently from a daily-use shower. The buyer should have the solution validated by the plumbing designer rather than rely on a general “anti-odour” promise.

Coordinate Waterproofing, Slope and Maintenance

A channel or floor drain is part of a system that includes the substrate, slope, screed, membrane, adhesive, tiles, joints and the drainage network. Ask for a drawing of the interface and check how the membrane is connected to the body. Responsibilities among the drain supplier, the waterproofing contractor and the tiler must be defined.

Access to the basket, the trap or the removable parts must remain possible after installation. Check how the grate is removed, which parts need cleaning and which can be replaced. The guide to wholesale sanitaryware in Turkey helps coordinate the other bathroom fittings.

Approve a Sample and Run Batch Inspections

Test the sample with a representative pipe, basin or shower mock-up. Check dimensions, connection, gaskets, pop-up mechanism where applicable, grate stability, removal, drainage and leakage using a suitable procedure. Document the reference and any corrections before production.

For the batch, inspect several cartons and pallets. Compare references, critical dimensions, finish condition, kit contents and accessories. The documents requested vary by market; they must cover the materials and models offered. The guide to buying materials in Turkey sets out a general method for inspections and supplier files.

Compare MOQ, Spare Parts and Packaging

For wholesale drains and shower channels, the MOQ may apply by length, grate, finish or outlet type. Ask whether several dimensions can be grouped together and whether replacement gaskets, baskets, membranes or mechanisms have a separate minimum.

Each visible finish must be individually protected against scratches. Internal parts and gaskets must stay with their body. Confirm units per carton, dimensions, weight, pallets and stacking limits. Long channels require rigid packaging that prevents twisting and impact during handling.

Compare offers on the complete kit, including accessories, packaging, inland transport, inspection and freight. The guide to the price of a wholesale bathroom pack provides context for budgeting related fittings without confusing product price with delivered cost.

RFQ Checklist for Drains and Channels

  1. Attach plumbing plans and bathroom details.
  2. Separate floor drains, plugs and linear channels.
  3. State dimensions, height, outlet and connection.
  4. Define material, finish, grate and accessories.
  5. Specify flow rate, water seal and anti-odour criteria.
  6. Request the detail of the interface with waterproofing.
  7. Test a sample in a representative configuration.
  8. Confirm spare parts, MOQ and lead time.
  9. Request cartons, pallets, weight and total CBM.
  10. Set the Incoterm, payment and handling of non-conformities.

Frequently Asked Questions

What is the difference between a plug and a trap?

The plug connects the fixture opening to the drainage, while the trap generally creates a barrier against odours. Some products combine several functions.

What is the MOQ for wholesale drains?

It varies by model, finish, length and packaging. Ask for the minimum per reference and whether several dimensions can be combined.

How do I choose between a vertical and a side outlet?

Use the plans, the available height and the route of the pipework. The direction, position and diameter must be confirmed before ordering.

Should a shower channel be tested?

Yes. Check the connection, stability, removal, drainage, kit watertightness and interface with the membrane in a representative mock-up.

How do I verify the flow rate?

Define the value or method required by the project and request the data for the exact model. The downstream network must also be sized correctly.

What does an anti-odour trap mean?

The product may use a water seal, a membrane or another device. Ask for its principle, conditions of use and maintenance instead of relying on the label alone.

Which spare accessories should I plan for?

Depending on the model, plan for gaskets, baskets, water seals, membranes, pop-up mechanisms, grates or removal tools identified by reference.

How do I protect finishes during transport?

Separate the visible surfaces, secure the parts, use strong cartons and give long channels particular protection against twisting.

Can I mix several channel lengths?

Yes, if the supplier accepts the corresponding MOQs. Each length, grate and outlet must keep a clearly identified reference and packaging.

How do I request a quotation from TPI Exports?

Send plans, dimensions, outlets, materials, quantities, destination and required documents via the Contact Us page.

Decision handoff

Useful for your buying team?

Share or save this guide before the next supplier comparison.